PHY 1321 Lecture Notes - Lecture 1: Conservative Force

164 views3 pages

plumferret19

15 Nov 2018

School

Department

Course

Professor

For unlimited access to Class Notes, a Class+ subscription is required.

violetpug978 and 12 others unlocked

PHY 1321 Full Course Notes

Verified Note

7 documents

Document Summary

The small particles of mass 50g is launched from the with vc= 30 m/s at the angle 30 deg above the horizontal. What is the magnitude of the velocity when the particle hits the ground. The crate of mass 100kg is placed on a flat floor of the truck. The friction coefficients between the floor and the crate are usat=0. 2and 0. 4 the truck enters the turn of radius 10m. What is the maximum speed of the truck if the crate is to stay stationary. If m=2. 0 kg when the whole system is moving upward acceleration a=2m/s^2, what isnthrntension in n in string 1. The helium balloon of total mass =0. 200kg and volume 1m^2 is attached to the thin long rope of mass density of 1g/m. The coils of rope lay on the flat ground, so that as the balloon moves up the rope, unwinds without any resistance. How high will the balloon rise? (air density 1. 204 kg/m^2)

Related Questions

1. A block is placed on a plane whose angle of inclination is 30˚. The coefficients of static and kinetic friction for the block on the inclined plane are both 0.2. The block
(A) remains stationary on the inclined plane.
(B) accelerates down the inclined plane.
(C) travels down the inclined plane at a constant velocity.
(D) travels up the inclined plane at a constant velocity.
(E) accelerates up the inclined plane.

2. An object with a mass of 5.5 kg is allowed to slide from rest down an inclined plane. The plane makes an angle of 30˚ with the horizontal and is 72 m long. The coefficient of friction between the plane and the object is 0.35. The speed of the object at the bottom of the plane is?

3. A 5-kg object slides down a frictionless surface inclined at an angle of 30˚ from the horizontal. The total distance moved by the object along the plane is 10 meters. The work done on the object by the normal force of the surface is?

4. A mass m = 2.5 kg is sliding along a frictionless table with initial speed v as shown in the figure. It strikes a coiled spring that has a force constant k = 500 N/m and
compresses it a distance x=5.0 cm. The initial speed v of the block was..?

5. The graph shows how the position of a particle depends on time. Which choice is closest to the instantaneous speed of the particle at t = 3s?
(A) 0.40 m/s
(B) 0.67 m/s
(C) 0.75 m/s
(D) 1.50 m/s
(E) 2.22 m/s

6. Calculate the work done by a force, F = 2x i, along the
path (0, 0) -> P₁(2, 0) -> P2(2, 2).

turquoisearmadillo973

To practice Problem-Solving Strategy 6.1 Work and Kinetic Energy.

Your cat �Ms.� (mass 7.00kg ) is trying to make it to the top of a frictionless ramp 2.00m long and inclined 19.0? above the horizontal. Since the poor cat can�t get any traction on the ramp, you push her up the entire length of the ramp by exerting a constant 44.0N force parallel to the ramp. If Ms. is moving at 1.80m/s at the bottom of the ramp, what is her speed when she reaches the top of the incline?

A) What is the cat's speed v2 when she reaches the top of the incline?

B)This problem can also be done without the work�energy theorem.

Since the forces acting on the cat are constant, the cat is moving up the ramp with a constant acceleration. Therefore, if you know her acceleration, you can use the equations of motion for constant acceleration to find her final speed. Use Newton's 2nd law to find the magnitude a of the cat's acceleration

What is the cat's speed v2 when she reaches the top of the incline?

indigoporcupine719

I am so lost onwere to even begin. I just need help trying to find the Ñ² (angle)for part part 1 of the experiment if anyone can just explain how todo that and maybe give me a step-by-step example so I can finishthe rest. Thank you! Experiment 6 ~ Friction

Purpose:

In this lab, you will make some basic measurements of friction.You will measure the coefficients of staticfriction between several combinations of surfaces using aninclined plane, and you will measure the coefficient ofkinetic friction between two of the combinationsof surfaces you used in the static friction part of thisexperiment.

Part 1: StaticFriction

Theory:

The coefficient of static frictionm_s can be measured experimentally foran object placed on an inclined plane (a.k.a. ramp, a.k.a. hill).The coefficient of static friction is related to the criticalangle q_c for the ramp, at whichthe object just begins to slide. Using what we havecovered in class, you can derive this relationshipyourself! At this critical angle, static friction preventing theobject from sliding down the hill is just exactly equal to thecomponent of the objectâs weight along the hill. If the componentof the weight along the hill were just a little greater, it wouldovercome friction, and the object would start to slide down. Thefree body diagram for this situation will look like the figuresketched below. Use this diagram to find an equation that relatesm_s toq_c.

F_N = NormalForce = mg cos(Î¸)

F_F =Î¼_s x F_N = Î¼_s mg cos(Î¸)

Î£F_x = mA_x = F_Gx - F_F = ?

F_Gx = mgsin(Î¸)

Hint #1: the angle q of the incline is the same as theangle between the normal force N and the weightmg. Why?

Hint #2: The weight mg can be broken into twocomponents. One component is along the incline(W_H). The other component is âpressinginto the hillâ, and is equal in magnitude to the normal forceN. (This is an example of a situation where the normalforce is not equal to the weight!) Remember that you need to usethe normal force to calculate friction, sincef=mN. Now calculate what the angle ofthe incline should be, so that the component of the weight down thehill is just exactly balanced by friction.

Equipment:

For this lab you will need to share the following ramps andblocks with other lab groups:

Ramps Blocks

Aluminum Aluminum

ParticleBoard Brass

StainlessSteel Plexiglass

Plastic Copper

Rubber

Steel

Wood

Experiment:

Test at least 5 different combinations of materials. Record thematerial of the block and the ramp for each combination.

1. Measure and record the length of theinclined plane you will be using. (This is thehypotenuse of the right triangle!)

2. Place the block on the plane and begin tiltingthe plane just until the point when the block begins to slide.

3. Measure the height of the raisedend of the inclined plane at this point. (This is theopposite side of the right triangle!) You cancalculate the angle from the measurements of the two sides.

4. Repeat the height measurement at least 3 timesfor each combination of materials. Record all the measurements inthe table below. Then,

(a) calculate the angle from the measurements of the hypotenuseand opposite side you just obtained

(b) use the equation you derived above in order to calculate thecoefficient of kinetic friction from the angle.

Block: woodenblock Block: cooper

Ramp:particleboard Ramp: particle board

Length of ramp:0.61(m) Length of ramp: 0.61(m)

Height(m)	Ñ²	Ms	Height(m)	Ñ²	Ms
0.24			0.26
0.25			0.31
0.245			0.345

avg m_s: ______ s : _______ avg m_s: ______ s : _______

Block:aluminum Block:particle board block

Ramp: solidewood Ramp: solide wood

Length of ramp:0.605(m) Length of ramp: 0.605(m)

Height(m)	Ñ²	s	Height(m)	Ñ²	s
0.15			0.23
0.16			0.165
0.16			0.195

avg m_s: ______ s : _______ avg m_s: ______ s : _______

5. Remember that in class we said that friction does not dependon surface area. You can easily test whether or not this iscorrect. Choose a block/ramp combination not already tested, andmake sure the block is not a cube or cylinder. Place the block sothat the side with the larger surface area is in contact with theboard. Now measure the angle at which the block just begins toslide (by measuring the hypotenuse and opposite sides of thecorresponding right triangle). As before, calculate the coefficientof friction from the angle you measured, using your equation.Repeat this process with the side of the block with the smallersurface area in contact with the board. Enter this data in thesmall tables below.

Block (larger end) :_________ Block (smaller end):__________

Ramp:_______________ Ramp: ________________

Length of ramp:______(m) Length of ramp: ______(m)

Height(m)	s	Height(m)	s

avg m_s: ______ s : _______ avg m_s: ______ s : _______

Part 2: KineticFriction

Theory:

You can calculate the coefficient of kinetic friction,m_k, using a variation of the methodyou used for the coefficient of static friction. For thecoefficient of kinetic friction, you can use the same free bodydiagram as the one drawn on the first page. But now, thecombination of W_H and the force offriction will need to add up such that the block will slide at aconstant speed. Think of Newtonâs first and second laws when youset up this equation. Derive a relationship between the criticalangle and the coefficient of kinetic friction.

Experiment:

You can measure m_k using aprocedure similar to the one you used to measurem_s. This time, just pick twocombinations of materials. The combinations you pick for this partof the experiment have to be combinations you alreadyused for the static friction part of the experiment, because thepoint is to compare m_sandm_k!

1. Measure and record the length ofthe inclined plane you will be using.

2. Raise the plane high enough for the blockto begin moving. Begin lowering the plane just until the pointwhen the block begins to slow down. (Alternatively, raise theboard while tapping the block until block moves at a constantrate.)

3. Measure the height of the raisedend of the inclined plane at this point.

4. Repeat the height measurement at least 3times for each combination of materials. Record all themeasurements in the table below. Then,

(a) calculate the angle from the measurements of the hypotenuseand opposite side you just obtained

(b) use the equation you derived above in order to calculate thecoefficient of kinetic friction from the angle.

Block (from part 1) :_________ Block (from part 1):__________

Ramp:_______________ Ramp: ________________

Length of ramp:______(m) Length of ramp: ______(m)

Height(m)	k	Height(m)	k

avg m_k: ______ s : _______ avg m_k: ______ s : _______

Analysis:

Calculate the mean value and standard deviation of thecoefficient of static friction that you measured, for each set ofmaterials.

ramp/board pair		Standard deviation




(larger end)
(smaller end)

Calculate the mean value and standard deviation of thecoefficient of kinetic friction that you measured, for each set ofmaterials.

ramp/board

pair

Standard

deviation

Questions:

1. How do the values of m_s compareto the values of m_k? (Of course, youcan only compare them for the same pairs of materials.)

2. Is the relationship betweenm_sand m_kwhat you expected?

3. Of the two parts of the experiment, measurement ofm_sand measurement ofm_k, which had more sources of error?What were some of the sources of error?

4. Could m_k orm_s ever be greater than 1? Explain whyor why not.

5. Is the coefficient of friction the same as when the block wasstanding on its larger (or smaller) end?

6. Think about your results. Do they make sense when youconsider your everyday experiences?

PHY 1321 Lecture Notes - Lecture 1: Conservative Force

PHY 1321 Full Course Notes

Document Summary

Get access

Related textbook solutions

Physics: Principles with Applications

Related Documents

PHYS 221 Midterm: PHYS 221 Iowa State Exam3 F11 Solutions

PHY 2048 Midterm: 2048_Fall13_Exam2_WithSolutions

PH 125 Midterm: ph125_ex1_practice

Related Questions