CHM 109 Lecture Notes - Lecture 11: Sodium Chloride, Evaporation, Dynamic Equilibrium

118 views6 pages

raspberrylouse755

11 Dec 2016

School

Department

Course

Professor

For unlimited access to Class Notes, a Class+ subscription is required.

Document Summary

15 gases, liquids and solids (we skip section 15. 8 and 15. 11) we won"t do gases until the end of the semester so skip ch. Naming practice: ch3ch2ch3= propane, 3-hex-an-amine, 1-propanoic acid. 15. 0 the general nature of gases per the ideal gas theory (ch. Molecules in liquids touch each other so weak forces between them have an effect, unlike with gas particles which are too far apart. 15. 2 intermolecular forces (imfs) is the term for the attractions between molecules, as opposed to bonds (covalent and ionic) between the atoms inside a molecule. Non-covalent attractions is another term for the same thing. Vapors obey the gas laws because they are gases. Increasing temperature increases vapor pressure (charles law) Larger molecules have higher molar heats and bpts because they tend to have more imfs ex. : butane is a 4-c chain which is a gas at room temperature but 8-

Related Questions

Converting between Units of Pressure Gases are different from solids and liquids. In a sample of gas, the molecules are far apart. The gas molecules also move around and collide with each other as well as with the walls of the container. These collisions generate pressure. The pressure of a gas can be measured in different units. One convenient unit of measure is called the atmosphere (atm) because it is based on atmospheric pressure. At sea level, the average pressure is 1 atm. As you get higher in altitude, the pressure steadily drops until you leave the atmosphere, where the pressure is very close to 0 atm. The table below shows the different commonly used units of measuring gas pressure. Use this table in the pressure unit conversions. Unit Abbreviation 1 atm equivalent atmosphere atm 1.00 atm (exact) millimeters of mercury mmHg 760 mmHg torr torr 760 torr inches of mercury in.Hg 29.9 in.Hg pounds per square inch (psi) lb/in.2 14.7 lb/in.2 pascal Pa 101,325 Pa.

Part C

High-pressure liquid chromatography (HPLC) is a method used in chemistry and biochemistry to purify chemical substances. The pressures used in this procedure range from around 500 kilopascals (500,000 Pa) to about 60,000 kPa (60,000,000 Pa). It is often convenient to know the pressure in torr. If an HPLC procedure is running at a pressure of 5.81Ã10⁸ Pa , what is its running pressure in torr?

Express the pressure numerically in torr.

M 121 1 201 Ideal Gas Law (PV n Experiment to T ) Determine the Ideal Gas Constant R 1. Conduct basic measurements, measurement , mathematical calculations and conversions for of volume, pressure, and temperature: calculate percent error and account for sources of error in an e xperimental result name and by following safety proced ty experiments for a redox reaction by using equipment identifiable by form chemical calculations using mass, mole and volumes and idenify limitatios of measuring devices in order to state the uncertainty/significant figures in measurements and calculation results. 5. Demonstrate a proficiency in relating the chemistry of gases to everyday phenomenon. Introduction Molecules in gases have very little attraction for one another, because relative to their size, they are so far apart from each other. For this reason we can often assume that a gas behaves "idcally." meaning that the physical behavior of the gas is independent of the composition of the gas. If a gas behaves ideally, then its physical properties can be described by the Ideal Gas Equation: Let's consider why the variables in the ideal gas equation have the relationships expressed in Equation 1aã The ideal gas equation assumes that there are no attractive forces between gas molecules. One can picture two billiard balls bouncing off one another in a totally clastic collision. If these molecules are placed in a balloon the collisions will occur not only with each other but also with the wall of the balloon, causing the balloon to expand. This expansion can be measured as a volume (V). More molecules will cause more collisions and thus more expansion. Therefore the quantity of molecules or number of moles (n) is directly proportional to the volume, and thus volume and number of moles appear on opposite sides of the equation. Another factor to consider is the kinetic energy of these molecules. Kinetic energy is related to the temperature (T) of the molecules, in that the kinetic energy. If the collisions with the wall of the balloon are happening at a very high speed due to high kinetic energy, the collisions will be harder and more frequent and thus the wall of the balloon will be pushed out further (a larger volume) than if the kinetic energy were less. The result is that volume is also directly proportional to the temperature. This relationship is seen in Equation la with (T) on the right side of the equation and (V) on the left. higher the temperature the greater the considered. While the molecules inside the balloon are pushing the balloon out, there are also molecules in thea Finally the pressure of the outside environment (atmospheric pressure) needs to be 59

CHM 109 Lecture Notes - Lecture 11: Sodium Chloride, Evaporation, Dynamic Equilibrium

Document Summary

Get access

Related Documents

CHM 109 Chapter Notes - Chapter 15: Butane, Junkers J 1, Gas 5

CAS CH 102 Chapter Notes - Chapter 6: Ideal Gas Law, Kinetic Theory Of Gases, Combined Gas Law

CHEM463 Lecture Notes - Kinetic Theory Of Gases, Pneumatic Trough, Partial Pressure

Related Questions