If you were to use THF, or tetrahydrofuran instead of dicholormethane for this experiment, could you still successfully extract your caffeine? Why or why not? (Consider what is necessary for an extraction to work)

If you were to use an acidic water solution for this extraction rather than a basic one, could you still perform the extraction?â

The experiment is below. Just answer the above questions.

Introduction Caffeine is one of three legal, mind-altering drugs available in the U.S without a prescription. Two common sources of this drug are tea and coffee, both of which are prepared via extraction of the solid foodstuff with liquid water. In this lab you will extract caffeine from food samples with liquid solvents and quantify the amount obtained. Laborator Hypothesis: We can rank various tea and coffee samples by caffeine content by performing a solid-liquid extraction from the foodstuff, followed by analysis via thin-layer chromatography. Experiment: In a 50 mL Erlenmeyer flask were placed 2.0 g of black tea. Dichloromethane (15 mL) and 0.2 M NaOH (5 mL) were added successively, and the stoppered flask was swirled gently by hand for 10 minutes (note: avoid vigorous shaking, as it will cause an emulsion to form). The dicloromethane layer was separated from the leaves and the aqueous layer by vacuum filtration through 7 g Celite 545, and the leaves were washed with a further 15 mL dichloromethane. The combined dichloromethane solution was placed in a 50 mL round bottom flask and concentrated to a minimal volume (ca. 1 mL) via simple distillation. The remaining dichloromethane solutions was transferred to a watch glass via pipet, and the solvent was evaporated in a fume hood. The sample was evaluated by TLC (a mixture of methanol and ethyl acetate as the mobile phase, co-spotted with authentic caffeine). Data: What was your crude yield of caffeine? What was the mass percentage of caffeine in your food source'? Given that the materials we are interested in are UV active, compared to the TLC standard how would you characterize the purity of your caffeine extracts? Conclusions: Can you comment on the purity of your caffeine sample? For all samples your class worked with where does your foodstuff rank in terms of caffeine content? How much caffeine is reported for the typical serving of coffee or tea? How did your extraction and isolation compare with the typical serving?

If you were to run the experiment without using any celite, what would happen to the purity of your sample and why?

What practical purpose does the distillation serve in this experiment?

The experiment is below. Just answer the above questions.

Introduction Caffeine is one of three legal, mind-altering drugs available in the U.S without a prescription. Two common sources of this drug are tea and coffee, both of which are prepared via extraction of the solid foodstuff with liquid water. In this lab you will extract caffeine from food samples with liquid solvents and quantify the amount obtained. Laborator Hypothesis: We can rank various tea and coffee samples by caffeine content by performing a solid-liquid extraction from the foodstuff, followed by analysis via thin-layer chromatography. Experiment: In a 50 mL Erlenmeyer flask were placed 2.0 g of black tea. Dichloromethane (15 mL) and 0.2 M NaOH (5 mL) were added successively, and the stoppered flask was swirled gently by hand for 10 minutes (note: avoid vigorous shaking, as it will cause an emulsion to form). The dicloromethane layer was separated from the leaves and the aqueous layer by vacuum filtration through 7 g Celite 545, and the leaves were washed with a further 15 mL dichloromethane. The combined dichloromethane solution was placed in a 50 mL round bottom flask and concentrated to a minimal volume (ca. 1 mL) via simple distillation. The remaining dichloromethane solutions was transferred to a watch glass via pipet, and the solvent was evaporated in a fume hood. The sample was evaluated by TLC (a mixture of methanol and ethyl acetate as the mobile phase, co-spotted with authentic caffeine). Data: What was your crude yield of caffeine? What was the mass percentage of caffeine in your food source'? Given that the materials we are interested in are UV active, compared to the TLC standard how would you characterize the purity of your caffeine extracts? Conclusions: Can you comment on the purity of your caffeine sample? For all samples your class worked with where does your foodstuff rank in terms of caffeine content? How much caffeine is reported for the typical serving of coffee or tea? How did your extraction and isolation compare with the typical serving?

If you were to run the experiment without using any celite 545, what would happen to the purity of your sample and why? Be specific.

Why is Celite 545 labeled as 545? What makes it special?

If you were to use THF, or tetrahydrofuran instead of dicholormethane for this experiment, could you still successfully extract your caffeine? Why or why not? (Consider what is necessary for an extraction to work) Why is dichloromethane different from THF

Only answer what is above. The experiment is written below.

Introduction Caffeine is one of three legal, mind-altering drugs available in the U.S without a prescription. Two common sources of this drug are tea and coffee, both of which are prepared via extraction of the solid foodstuff with liquid water. In this lab you will extract caffeine from food samples with liquid solvents and quantify the amount obtained. Laborator Hypothesis: We can rank various tea and coffee samples by caffeine content by performing a solid-liquid extraction from the foodstuff, followed by analysis via thin-layer chromatography. Experiment: In a 50 mL Erlenmeyer flask were placed 2.0 g of black tea. Dichloromethane (15 mL) and 0.2 M NaOH (5 mL) were added successively, and the stoppered flask was swirled gently by hand for 10 minutes (note: avoid vigorous shaking, as it will cause an emulsion to form). The dicloromethane layer was separated from the leaves and the aqueous layer by vacuum filtration through 7 g Celite 545, and the leaves were washed with a further 15 mL dichloromethane. The combined dichloromethane solution was placed in a 50 mL round bottom flask and concentrated to a minimal volume (ca. 1 mL) via simple distillation. The remaining dichloromethane solutions was transferred to a watch glass via pipet, and the solvent was evaporated in a fume hood. The sample was evaluated by TLC (a mixture of methanol and ethyl acetate as the mobile phase, co-spotted with authentic caffeine). Data: What was your crude yield of caffeine? What was the mass percentage of caffeine in your food source'? Given that the materials we are interested in are UV active, compared to the TLC standard how would you characterize the purity of your caffeine extracts? Conclusions: Can you comment on the purity of your caffeine sample? For all samples your class worked with where does your foodstuff rank in terms of caffeine content? How much caffeine is reported for the typical serving of coffee or tea? How did your extraction and isolation compare with the typical serving?

CHM 2123 Study Guide - Separatory Funnel, Hexane, Caffeine

Document Summary

Get access

Related Documents

CHM 2123 Lecture Notes - Lecture 1: Sodium Bicarbonate, Deprotonation, Catechin

CHM 2123 Study Guide - Final Guide: Silica Gel, Cold Finger, Dichloromethane

CHM 1711 Lecture Notes - Lecture 3: Thin-Layer Chromatography, Silica Gel, Dichloromethane

Related Questions