CMSC 100 Lecture Notes - Lecture 6: Textedit

77 views3 pages

sapphiretiger55

21 Jul 2017

School

University of Maryland

Department

Computer Science

Course

CMSC 100

Professor

Deepa Anagondahalli

For unlimited access to Class Notes, a Class+ subscription is required.

Document Summary

When it comes to software for writing html, there is a lot of them. But you don"t need to go out and buy some fancy software costing . You can write html for free using notepad or. On windows 8 or higher, this is done by opening the start screen and typing in notepad. Then click on the notepad icon to open it. On windows 7 or earlier, you"ll need to dig a bit deeper. Open the start menu, go to programs then accessories and find. Step two: now that you"ve opened notepad, you gotta write some html code. Step three: now save the file on your computer and call it test. html. Note that the . html part is super important since that tells the computer that this is a html document and not a text file. Step four: now open the file in a web browser and the result should look something like this:

Related Questions

Learning Objectives

After successfully completing this assignment, students will be able to:

Configure, run, and test a linux server in AWS' EC2
Configure, run, and test a Windows server in AWS' EC2

Requirements

Create an Ubuntu 20 LAMP server in EC2 like we did in class.
Verify your that Apache was installed by opening your browser and enter the public dns of your server in the address bar. If it does not connect either you did not add HTTP to the Security Group, or the install did not work properly. Take a screenshot and save it (for submission below).
The default location of html and php files is /var/www/html. Change to that directory. Now, using your favorite text editor use sudo to run your editor and create a file in that directory named info.php. For example, sudo nano info.php Then enter the following in that file to show information about the PHP installation: <?php phpinfo(); ?> Save the changes to the file and exit the editor.
Now in your browser, enter the public dns of your server in the address bar / info.php. For example, my public dns was ec2-54-89-230-235.compute-1.amazonaws.com, so I enter as the url. Take a screenshot and save it (for submission below).
Create a Windows 2016 Server, like we did in class.
Login to it using Remote Desktop. Take a screenshot of Remote Desktop connected to your Windows Server and save it (for submission below).

Clean Up

Now that you have completed the assignment, stop or terminate your EC2 instances. Stopping them means that it is now longer running, but your data is saved. That means you will not accrue charges on your running server. Terminating will both stop and delete the instances (also not accruing charges).

What to Submit

Screenshot of Apache page on your server shown in your browser
Screenshot of the PHP info page on your server shown in your browser
Screenshot of Remote Desktop session to your Windows Server

jayson

Grade 9 Science – Lab Safety & Equipment Woksheet

Part A: Highlight ‘T’ for TRUE OR ‘F’ for FALSE for each of the following questions. (K - 35)

1. T F Broken glassware should be swept up immediately and placed in the garbage bin.
2. T F Eyeglasses or contact lenses are an acceptable substitute for googles during an experiment.
3. T F If you arrive at class to find a spilled liquid on your desk, you should assume it is water and wipe
it up with paper towels.
4. T F Students with long hair must tie it back when using Bunsen burners.
5. T F If you take too much of the chemicals needed for an experiment, put it back into the container you
got it from.
6. T F Class B fires are those related to electrical equipment.
7. T F Discard all solid waste by rinsing it down the sink.
8. T F You may consume food and drinks during a lab, as long as it is kept at a safe distance from
chemicals.
9. T F If asked to detect the odour of a chemical in the lab, the student should inhale a deep breath of the
chemical.
10. T F If your clothing were to catch on fire, your first step should be to STOP, DROP and ROLL.
11. T F When using a fire extinguisher, aim at the top of the fire. The chemical in the extinguisher will
fall and put out the flames.
12. T F When heating chemicals in a test tube, heat from the bottom up, aiming the test tube at the
ceiling, and keep the test tube still.
13. T F It is ok to take off my safety goggles if it’s just for a second while I write something down.
14. T F If any chemical makes contact with your eye, wash it immediately at the eyewash station for
fifteen minutes. If you should spill chemicals on your skin, place the affected area under water
immediately.
15. T F Always read through each activity before you begin.
16. T F If you are unsure about any part of the procedure for an experiment, you should figure it out
yourself. Asking the teacher for clarification will result in a lower mark due to lack of preparation.
17. T F It is acceptable to sit during very long experiments.
18. T F It is ok if I don’t know where the lab safety equipment is since I can just ask someone later.
19. T F Be sure to tell your teacher about any accident, broken equipment, or injury that occurs during
class; no matter how minor.
20. T F When working with chemicals, keep pens and pencils away from your mouth.
21. T F In warmer months, it is acceptable to wear sandals during an experiment.
22. T F Determine whether your equipment is cool enough to disassemble by placing the back of your
hand near it.
23. T F Loose-fitting, long-sleeved shirts should be worn during experiments to protect your arms from
burns and chemical splashes.
24. T F If you must retrieve materials during a lab, it is acceptable to leave your Bunsen burner unattended
as long as it is set to a yellow flame.
25. T F To avoid an injury when heating materials, always place a stopper or tight-fitting lid on the
container being heated.
26. T F If a student uses the last of the chemicals in an experiment, it is their responsibility to go into the
storeroom to retrieve an additional quantity of that chemical.
27. T F Always leave your work area clean and dry before leaving the lab and make sure equipment and
glassware is returned clean to its proper place.
28. T F Horseplay is O.K. during a lab as long as no one is getting hurt.
29. T F It is never advisable to place a thermometer in an open flame.
30. T F To cool hot glassware, run cold water over it.
31. T F Class A fires can be extinguished with water.
32. T F Class D fires must be extinguished with water.
33. T F Keep equipment away from the edge of the lab bench.
34. T F If your eye itches while you are working with chemicals, you should rub it with your hands.
35. T F WHMIS stands for warning hazardous materials information symbols.

jhonny

CMSC 100 Lecture Notes - Lecture 6: Textedit

Document Summary

Get access

Related Documents

CS100 Lecture Notes - Lecture 7: Web Browser, Text Editor, Filename Extension

Computer Science 1032A/B Lecture Notes - Xml Namespace, Unicode, International Standard Book Number

Computer Science 1032A/B Study Guide - Uniform Resource Locator, Markup Language, Text File

Related Questions