answers

watching

views

26 Nov 2019

A 10.0 g sample of compound A is dissolved in 50 mL of water. Thissolution is mixed with
50 mL of diethyl ether. The mixed system separates into two layersof equal volume. If the
partition constant (K) for compound A in this system is 2.8, howmany g of A will be
transferred to the organic layer? How many g of A remain in theaqueous layer?
If the aqueous layer from the extraction described above isseparated and then extracted a
second time, using fresh diethyl ether, how many g of A will betransferred to the new ether
layer? (K remains the same, even though the number of g of A beingpartitioned is smaller.
How many total g of A have been extracted into the two etherfractions?
Problem 2
If 50 mL of an aqueous solution containing 10 g of A is mixed with100 mL of diethyl ether,
how many g of A will be transferred to the organic layer? (K isstill the same, but there is twice
as much ether as water.) Compare the amount of A extracted by twoextractions using 50 mL of diethyl ether each to
the amount extracted by a single 100 mL extraction of the ether.Which is more efficient?

answers

watching

156

views

For unlimited access to Homework Help, a Homework+ subscription is required.

Join us on Discord

Chemistry Study Group

Join now

Related questions

I'm currently taking ochem part 2. I need to perform an acid-base extraction to separate out a mixture of solid organic compounds consisting of 50% 2-chlorobenzoic acid; 40% methyl 4-aminobenzoate; 10% 1,4-dibromobenzene. I need to create a procedure to first separate the compounds. I also need to recrystallize each compound after separating the compounds; therefore, I need to know which solvent to use for each compound. I also need to prove that I separated my compounds successfully using TLC (therefore I need to know which solvent to use for TLC). I need to do this as a micro-scale procedure (therefore, I will not be given large quantities of reagants). I'm given the reagants methanol, ethanol, methylene chloride, hexane, 1M NaOH, 6M NaOH, 1M HCl, 6M HCl, Anhydrous sodium sulfate, saturated sodium chloride, acetone, sodium bicarbonate, diethyl ether. I believe we will be given about 2 grams of the solid organic compound mixture.

Note: I want to run this acid-based extraction without using the separation funnel. Can I use a centrifuge tube instead?

I have a rough procedure of how to carry out the acid-base extraction that I've posted below, please look over my rough procedure of the acid-based extraction portion and tell me if the amounts of reagants look okay and if the process is okay. I also have accompanied this with a couple of follow up questions in regards to the acid-based extraction, recrystallization, and running the TLC all accompanied with subheadings.

OFFICIAL PROCEDURE:

Put 0.090g of solid organic mixture into a large test tube. Add 0.5 mL of diethyl ether at a time and stir until all dissolves. If needed, slowly add more diethyl ether solvent. Use minimal solvent.

Extracting methyl 4-aminobenzoate

1. Add this mixture in large test tube into a glass centrifuge tube (labeled âworking reactionâ).

2. Add 1mL 1.0 M HCl to the centrifuge tube. Shake gently and vent. Do this until layers separate. If needed, centrifuge.

Diethyl ether density: 0.713 g/cm3

Waterâs density: 1.00g/cm3 (aqueous layer)

Because diethyl ether has a lower density, it will be on the top layer and consist of the 1,4-dibromobenzene and the 2-chlorobenzoic acid. The bottom aqueous layer will consist of the conjugate acid of the organic base, methyl 4-aminobenzoate because H3O+ protonates the amine of the base to produce an ammonium salt, which is ionic and therefore aqueous in solution. (DRAW THIS OUT)

3. Extract out lower aqueous layer (consisting of the conjugate acid i.e. the ammonium salt, of methyl 4-aminobenzoate) into labeled test tube (ammonium salt).

Note: It is okay to extract a little more out from the bottom bleeding into the organic layer; throw that into the waste to ensure that all that is left are the other 2 organic compounds in diethyl ether. Parafilm.

4. Into the test tube with the ammonium salt, add 6.0 M NaOH DROP BY DROP until the solution returns to become BASIC, this has reproduced the organic base, methyl 4-aminobenzoate. Check with pH paper.

5. Collect the crude methyl 4-aminobenzoate precipitate by filtration using Buchner funnel.

6. Recrystallize from HOT WATER.

6. Filter the pure methyl 4-aminobenzoate precipitate by filtration using Buchner funnel.

Extracting 2-chlorobenzoic acid

1. The âworking reactionâ centrifuge tube now consists of the solvent (diethyl ether), 1,4-dibromobenzene, and 2-chlorobenzoic acid. Add 1 mL of 1.0 M NaOH. Shake and vent. Centrifuge if necessary. Again, as before, the lower layer is aqueous and the top layer is the organic layer (diethyl ether + 1,4-dibromobenzene)

NOTE: B/c NaOH was added, the 2-chlorobenzoic acid was deprotonated to yield a sodium salt, which produced its conjugate base. The salt is ionic and therefore soluble in water.

2. Extract out the bottom layer with Pasteur pipette (contains conjugate base of 2-chlorobenzoic acid) into test tube labeled sodium salt.

Note: It is okay to extract a little more out from the bottom bleeding into organic layer; throw that out into the waste to ensure that all that is left is 1,4-dibromobenzene in diethyl ether. Parafilm.

3. Into the test tube with the sodium salt, add 6.0 M HCl DROP BY DROP until the solution returns to become ACIDIC. This has now reproduced the organic acid, 2-chlorobenzoic acid.

4. Recrystallize with what solvent?

Extracting 1,4-dibromobenzene

1. The âworking reactionâ centrifuge tube should now only contain diethyl ether, 1,4-dibromobenzene with some potential water. Add sodium sulfate to dry out the remaining water. Extract the solution (leaving behind the sodium sulfate ppt) into a test tube labeled 1,4-dibromobenzene.

2. Place the test tube labeled â1,4-dibromobenzeneâ in a hot water bath and boil to that of the solvent (diethyl ether) at 40C.

3. Diethyl ether has a low boiling point of 34.6 C whereas 1,4-dibromobenzene has a high boiling point of 220.4C.

4. Therefore, the remaining organic layer in the âworking reactionâ centrifuge tube now only containing 1,4-dibromobenzene and diethyl ether can be separated by evaporating diethyl ether.

5. Recrystalize with what solvent?

Acid-Based Extraction Questions:

Q1: Is diethyl ether a good solvent for initially dissolving all three solvents for the acid-base extraction? And if so, how much solvent do I need to add? I thought minimal enough to dissolve the organic comopunds?

Q2: Are my rough amounts of reagants used correctly for the acid-base extraction?

Q3: Should I add anhydrous sodium sulfate to my last step of acid-base extraction which consists of the diethyl ether and 1,40-dibromobenzene because there might be some aqueous layer left?

Q4: Can I perform my acid-base extractions with a centrifuge tube instead of a separation funnel?

Q5: Should I start off with more grams of my organic mixture when I begin? Is 0.090 grams too small?

Recrystallization Question

Q6: Which solvents for each isolated crude compound should I use for recrystallization? Do I need to run a test for a suitable solvent? If so, which solvents are good to start with. I was thinking water and methanol.

a) I was thinking of using hot water as the hot solvent for methyl 4-aminobenzoate and for 2-chlorobenzoic acid. Is this correct to do so?

b) Which solvent should I also use to recrystallize 1,4-dibromobenzene?

TLC Question

Q7: Which solvent should I use to run the TLC for my organic compounds. After I know which solvent I will be using, where should I expect each compound to travel relative to the other organic compounds? (i.e. closest to the solvent line, middle of the solvent line, furthest from solvent line).

Miscellaneous Question

Q8: What's the point of telling me the percentages of the compounds in the mixture? Does that affect how much reagant I should be using during the acid-based extraction?

5. Assume that the partition coefficient, K, for partitioning of compound Abetweendiethyl ether and water is 3; that is, A preferentially partitions into ether.a. Given 400 mL of an aqueous solution containing 12 g of compound A, howmany grams of A could be removed from the solution by a single extractionwith 200 mL of diethyl ether?b. How many total grams of A can be removed from the aqueous solution withthree successive extractions of 67 mL each?*if given the equation can you please explain how you got it and what the numbers mean in it (if some numbers or standard or the plug in's you took from the question I asked you )-thanks :)

viridianlocust958

Organic chemistry question about extraction lab...?
Procedure:
Place 2.0 g of the mixture of sucrose, acetylsalicylic acid and acetanilide into a 125 mL Erlenmeyer flask.
Add 50 mL of methylene chloride (dichloromethane) and dissolve as much of the solid as possible.
Remove the insoluble sucrose via gravity filtration using fluted filter paper. Allow to dry until the next lab period.
Add the methylene chloride solution to the separatory funnel and extract it with two 25 mL portions of 5 % sodium bicarbonate (aqueous).
Place the combined aqueous layers into a 400 mL beaker and add enough concentrated hydrochloric acid to make it very acidic (less than pH of 2) â approximately 10 mL
Allow the solid to crystallize from the aqueous layer. Chilling in an ice bath may be required.
When lots of solid has been formed, collect the solid by vacuum filtration. Wash the solid with approximately 5 mL of cold water
Allow the solid to dry open until the next lab period.
Dry the organic layer (methylene chloride) over anhydrous sodium sulfate.
Decant the solvent from the drying agent (or gravity filter through fluted filter paper) into a clean, dry a pre-weighed 100 mL round-bottom flask.
Evaporate the solvent using rotary evaporation and allow the residue to dry open over the week.
The following lab period, weigh all 3 solids, take the melting points of all 3 solids and calculate the percent composition of the original solid.

Drying agents:
Equations for drying agents:
MgSO4 (s) + 7 H2O(l) ï MgSO4.7H2O(s)
CaSO4(s) + 2 H2O(l) ï CaSO4.2H2O(s)
CaCl2(s) + 6 H2O(l) ï CaCl2.6H2O(s)
Na2SO4(s) + 7 H2O(l) ï Na2SO4.7H2O(s)

1. The original organic solution was extracted two times with aqueous sodium bicarbonate. After the extraction, what compound(s) were in the organic layer? What compound(s) were in the aqueous layer?

________________________________________________________________________________________________________________________________________________________________________________________________________________________

2. Assume that both acetylsalicylic acid and acetanilide are soluble in diethyl ether, and that diethyl ether was used in place of the methylene chloride. Would the ether layer be the bottom layer in the separatory funnel or the top layer? Explain your answer.

3. Assume that both acetylsalicylic acid and acetanilide are soluble in methanol, and that methanol was used in place of the methylene chloride. What problem(s) might occur during the extractions? (Careful, this is a trick question.)

4. Historically, the solid residue that is left after the methylene chloride solution is evaporated has a lower melting point that its literature value, due to impurities. Explain what impurities are present and why.

Weekly leaderboard

Home

Homework Help 3,900,000

Chemistry 830,000

Related textbook solutions

Basic Chemistry

Principles of Chemistry Molecular Approach

Principles of Chemistry Molecular Approach

Chemistry: Structure and Properties

Chemistry: A Molecular Approach

Chemistry: A Molecular Approach

Principles of Chemistry: A Molecular Approach

Chemistry: The Central Science

Related questions

Weekly leaderboard