Table sugar (or sucrose, a disaccharide made of the monomersglucose and fructose) is dissolved in water at room temperature. Aresearcher cannot detect smaller components (glucose, fructose, CO2and other fragments) because A. The sucrose has lessfree energy than its components.
B. Breaking apartsucrose to make CO2 is endergonic.
C. The activation energybarrier cannot be overcome by the sucrose molecules.
D. Tearing apart sucroseto form CO2 is not a spontaneous reaction.
| A. The sucrose has lessfree energy than its components. | |
| B. Breaking apartsucrose to make CO2 is endergonic. | |
| C. The activation energybarrier cannot be overcome by the sucrose molecules. | |
| D. Tearing apart sucroseto form CO2 is not a spontaneous reaction. |
For unlimited access to Homework Help, a Homework+ subscription is required.
Related textbook solutions
Related questions
Experiment 1 Fermentation by Yeast Experiment Inventory Labware (4) 250 mL Beakers (1) 100 mL Graduated Cylinder (1) Test Tube Rack (5) Fermentation Tubes = (10) Test Tubes (5 plastic and 5 glass; see Figure 4) (1) Measuring Spoon (4) Pipettes (1) Ruler Note: You must provide the materials listed in *red. EXPERIMENT 1: FERMENTATION BY YEAST Yeast cells produce ethanol, C2 H6 O, and carbon dioxide, CO2 , during alcoholic fermentation. In this experiment, you will measure the production of CO2 to determine the rate of fermentation in the presence of different carbohydrates with fermentation tubes. Note: Regular table sugar is sucrose, a disaccharide, which is made up of glucose and fructose. Glucose is a monosaccharide. Figure 4: Fermentation tubes. Note how the smaller, plastic test tube is inverted into the larger glass tube. You will create five fermentation tubes in this experiment. PROCEDURE 1. In this experiment, you will mix yeast with sugar, Equal®, and Splenda®. Before you begin, develop a hypothesis predicting what will happen when the sugar/sweeteners are mixed with yeast. Will fermentation occur? Why or why not? Record your hypothesis in the post-lab questions. 2. Use the permanent marker to label three 250 mL beakers as Equal®, Splenda®, and Sugar. 3. Empty the Equal®, Splenda®, and Sugar packets into the corresponding beakers. 4. Fill the Equal® and Splenda® beakers to the 100 mL mark with warm tap water. 5. Fill the Sugar beaker to the 200 mL mark with warm tap water. 6. Mix each beaker thoroughly by pipetting the solution up and down several times. Use a new pipette to mix each solution. Each beaker now contains a 1% solution. Set these aside for later use. 7. Completely fill one of the smaller plastic tubes with tap water and invert the larger glass tube over it. Push the small tube up into the larger tube until the top connects with the bottom of the inverted tube. Invert the fermentation tube (Figure 4) so that the larger tube is upright (there should be a small bubble at the top of the internal tube). Note: Repeat Step 7 several times as practice. Strive for the smallest bubble possible. When you feel comfortable with this technique, empty the test tube(s) and proceed to Step 8. CAUTION: Do not try to force the plastic test tube into the glass test tube. This might cause your glass test tube to break, causing you injury. If your plastic test tubes do not fit easily, please call eScience Labs for replacement glass tubes. If you are able to set up at least two fermentation tubes, continue with the experiment, but know that you will have to perform steps 12-15 in multiple steps. 8. Use the permanent marker to label the fourth 250 mL beaker as Yeast. 9. Fill this beaker with 175 mL of warm tap water. It should be between 30 and 40o C (warm to the touch). 10.Open the yeast package, and use the measuring spoon to measure and pour 1 tsp. yeast into the beaker. Pipette the solution up and down until all of the yeast is mixed homogenously into the solution. Note: Make sure the yeast solution remains homogenous before each test tube is filled in the proceeding steps. The yeast density is fairly high, and the yeast may settle to the bottom of the beaker if it rests for an extended period of time. 11. Use the permanent marker to label the big glass and small plastic test tubes as 1, 2, 3, 4, and 5. 12.Use the 100 mL graduated cylinder to measure and pour 15 mL of the following solutions into the corresponding small plastic test tubes: Tube 1: 1% Glucose Solution Tube 2: 1% Sucrose Solution Tube 3: 1% Equal® Solution Tube 4: 1% Splenda® Solution Tube 5: 1% Sugar Solution Note: Thoroughly rinse the graduated cylinder between each measurement. 13.Fill the remaining volume in each small tube to the top with the yeast solution. 14.Slide the corresponding larger tube over the small tube and invert it as practiced in Step 7. This will mix the yeast and sugar/sweetener solutions. 15.Place the fermentation tubes in the test tube rack, and use a ruler to measure (in millimeters) the initial air space in the rounded bottom of the internal tube. Record these values in the Table 1. 16.Allow the test tubes to sit in a warm place (approximately 30 °C) for two hours. Placement suggestions include: a sunny window sill, atop (not in!) a warm oven heated to approximately 85 °C (185 °F on an oven setting), or under a very bright (warm) light. 17.At the end of the fermentation period, use your ruler to measure (in millimeters) the final gas height (total air space) in each tube. Record this data in Table 1. 18.Calculate the difference between the initial and final gas height in each tube. Record this data in Table 1.
EXPERIMENT 1: FERMENTATION BY YEAST
Result Tables
Table 1: Yeast Fermentation Data
| Tube | Initial Gas Height (mm) | Final Gas Height (mm) | Net Change (mm) |
|---|---|---|---|
| 1 | |||
| 2 | |||
| 3 | |||
| 4 | |||
| 5 |
Post-Lab Questions
Include your hypothesis from Step 1 here. Be sure to include at least one piece of scientific reasoning in your hypothesis to support your predictions.
Did you notice a difference in the rate of respiration between the various sugars? Did the artificial sugar provide a good starting material for fermentation?
Was anaerobic fermentation occurring? How do you know (use scientific reasoning)?
If you observed respiration, identify the gas that was produced. Suggest two methods you could use for positively identifying this gas.
Hypothesize why some of the sugar or sweetener solutions were not metabolized, while others were. Research the chemical formula of Equal® and Splenda® and explain how it would affect yeast respiration.
How do the results of this experiment relate to the role yeast plays in baking?
What would you expect to see if the yeast cell metabolism slowed down? How could this be done?
Indicate sources of error and suggest improvement (for example, what types of controls could be added?).